Fluke 9105 Bedienungsanleitung PDF herunterladen (Seite 61)

•

The over-temperature cut-out should be checked every 6 months to see

that it is working properly. In order to check the user selected cut-out, fol

low the controller directions (Section 8.2) for setting the cut-out. Both the

manual and the auto reset option of the cut-out should be checked. Set the

instrument temperature higher than the cut-out. Check to see if the display

flashes cut-out and the temperature is decreasing.

58 Hart Scientific

12 Maintenance

1 2 ... 56 57 58 59 60 61 62 63 64 65

9105 / 9107 1
Dry-well Calibrator 1
Rev.2A2801 2
Table of Contents 3
1.2 Safety Information 9
9105/9107 3 10
1 Before You Start 10
Figure 1 Top View 10
Cautions 11
9105/9107 5 12
6 Hart Scientific 13
2 Introduction 14
3.1 Specifications 15
3.2 Environmental Conditions 15
3.3 Warranty 16
4 Safety Guidelines 17
12 Hart Scientific 18
5 Quick Start 19
5.4 Setting the Temperature 20
6 Parts and Controls 21
6.2 Front Panel 22
3/16" Well 23
1/4" Well 23
1/8" Well 23
6.4 Well Insulator (9107only) 24
9105/9107 19 25
7 General Operation 26
7.3 Setting the Temperature 27
7.4 Calibrating Probes 27
8 Controller Operation 28
Temperature 29
8.3 Temperature Set-point 30
8.4 Scan 31
8.5 Temperature Display Hold 32
8.5.2 Mode Setting 33
9105/9107 29 34
30 Hart Scientific 35
9105/9107 31 36
Figure 7 Switch Test Data 36
32 Hart Scientific 37
8.7 Secondary Menu 39
8.8 Heating Power 39
8.9 Proportional Band 39
-12 Pct 40
8.10 Cut-out 41
8.11 Controller Configuration 42
8.11.2 Operating Parameters 43
8.11.2.3 Soak Stability 44
8.11.3.1 BAUD Rate 44
8.11.3.2 Sample Period 45
8.11.3.3 Duplex Mode 45
8.11.3.4 Linefeed 45
8.11.4.1 IEEE-488 Address 46
8.11.4.2 Termination 46
8.11.5 Calibration Parameters 47
9.1 Serial Communications 48
9.1.2.1 BAUD Rate 49
9.1.2.2 Sample Period 49
9.1.2.3 Duplex Mode 49
9.1.2.4 Linefeed 49
9.2 IEEE-488 Communication 50
9.3 Interface Commands 51
10 Test Probe Calibration 55
10.2 Dry-Well Characteristics 56
10.2.1 Vertical Gradient 57
11 Calibration Procedure 58
56 Hart Scientific 59
12 Maintenance 60
58 Hart Scientific 61
13 Troubleshooting 62
13.2 Comments 63
13.3 Wiring Diagrams 64
62 Hart Scientific 65
Figure 11 9107 Wiring Diagram 65

Kommentare zu diesen Handbüchern

Keine Kommentare

Fluke 9105 Bedienungsanleitung Seite 61

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Fluke 9105